Viper Automobile Alarm Model 480XV User Manual

Model 480XV  
Owner’s Guide  
 
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM  
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER  
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.  
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY  
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY  
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE  
AUTHORISED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.  
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-  
ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,  
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF  
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY  
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER  
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-  
TROL MODULE AS DESCRIBED ABOVE. Some territories do not allow limitations  
on how long an implied warranty will last or the exclusion or limitation of incidental or  
consequential damages. This warranty gives you specific legal rights and you may also have  
other rights that vary from State to State or country to country.  
Directed security systems, including this unit, are deterrents against possible theft.  
Directed is not offering a guarantee or insurance against vandalism, damage or theft of the  
automobile, its parts or contents; and hereby expressly disclaims any liability whatsoever,  
including without limitation, liability for theft, damage and/or vandalism. Directed does  
not and has not authorised any person or entity to create for it any other obligation,  
promise, duty or obligation in connection with this security system.  
Make sure you have all of the following information from your dealer:  
A clear copy of the sales receipt and installation certificate, showing the following:  
Date of purchase  
Your full name and address  
Authorised dealer's company name and address  
Type of alarm installed  
Year, make, model and colour of the vehicle  
Vehicle registration number  
Vehicle identification number  
All security options installed on the vehicle  
© 2005 directed electronics, inc.  
4
 
table of contents  
limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
2-way LCD remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . 7  
LCD screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
standard remote configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
what is included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
2-way LCD remote control functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
standard configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
standard LCD icon configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 18  
system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
out of range notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
programming LCD remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
To enter programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Beeps/Vibration On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Illumination On/Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Page notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
To exit programming mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
using your system . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
one-time bypass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
transmitter sensor disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
autoimmobilisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
disarming without a transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
entering your PIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
interior light control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . 32  
disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
interpreting zone diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
high frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
© 2005 directed electronics, inc.  
5
 
vehicle recovery system (vrs®) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
arming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
vrs® triggered sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
disarming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
ultrasonic sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
health check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
© 2005 directed electronics, inc.  
6
 
2-way LCD remote control  
6
3
4
5
2
1
7
1.  
2.  
3.  
4.  
5.  
6.  
7.  
Auxiliary Channel Button  
Arm Button  
LCD Screen (see LCD Screen)  
Disarm Button  
Not Used  
Battery Compartment  
Program Button  
© 2005 directed electronics, inc.  
7
 
LCD screen  
1 2 3 4  
5
6
7
23  
22  
21  
8
9
10  
20  
11  
12  
19  
18  
17  
13  
16  
15  
14  
1. Transmit  
2. Out of range  
3. Receive  
13. Battery  
14. Remote start (option)  
15. Field disturbance sensor  
16. Ultrasonic sensor setting  
17. Vibrate On  
4. Auxiliaries  
5. Garage door (519H option)  
®
6. Warn Away  
18. Ignition  
7. Alarm  
19. Hood (Bonnet)  
20. Vehicle number  
21. Door  
8. Ultrasonic sensor  
9. Tilt sensor  
10. Trunk (Boot)  
11. Glass breakage sensor  
12. Shock sensor  
22. Arm  
23. Disarm  
© 2005 directed electronics, inc.  
8
 
standard remote configuration  
Lock–Arm  
controls the  
function.  
Unlock–Disarm  
controls the  
function.  
Silent Mode™  
Channel Output (2)  
.
controls  
and an  
Not Used.  
Channel Output (3)  
.
and  
pressed together control an  
pressed together control an  
pressed together control an  
pressed together control an  
Channel Output (4)  
and  
.
Channel Output (5)  
and  
and  
.
Channel Output (6)  
.
© 2005 directed electronics, inc.  
9
 
P
(located on back of the remote) selects the vehicle to control  
and also provides user selection of LCD remote response .  
what is included  
Control module and ultrasonic sensors  
1 four-button 2-way LCD transmitter  
1 four-button transmitter  
Wire harnesses  
515ESP Battery Backup siren  
Blue status LED indicator light  
A push-button Valet switch  
Your warranty registration  
548T transceiver/antenna  
important information  
Congratulations on the purchase of your state-of-the-art vehicle  
security system. This system has been designed to provide years  
of trouble-free operation. Due to the complexity of this system,  
it must be installed by an authorised dealer only. Installation of  
this product by anyone other than an authorised dealer voids the  
warranty. All dealers are provided with preprinted dealer certifi-  
cates to verify that they are authorised.  
This owner’s guide should help you to get the most out of your  
system. Please take the time to read it prior to using the system.  
© 2005 directed electronics, inc.  
10  
 
note:  
Your system MUST be installed by an Authorised dealer in accor-  
dance with the instructions we supply them. The Viper 460XV system  
is designed to be installed in any petrol or common rail diesel vehicle  
with a 12-volt battery.  
note:  
The Installation Certificate must be completed by your installer at  
the authorised dealer. Other than the remote controls, this system has no  
user-serviceable parts. Your authorised dealer can correct any system  
wiring problems and, if needed, can return any malfunctioning compo-  
nent to Directed Electronics for repair/replacement under the terms of  
the Limited Lifetime Warranty printed at the beginning of this guide.  
note:  
Making changes to the existing system will invalidate the certifi-  
cate of installation.  
system maintenance  
This system needs no specific maintenance beyond remote  
control battery replacement. The LCD remote is powered by a  
1.5V  
AAA battery.  
The Battery Level indicator has four level indicators that serve as  
a visual indication of battery charge. When the battery reaches a  
low charge level that requires replacement, the remote control  
will generate a single notification chirp, and the Battery Level  
indicator will flash continuously.  
FULL  
EMPTY  
REPLACE  
Battery Replacement  
Gently pull the end of the battery door away from the top of the  
remote control then slide the door up to expose the battery and  
remove the expired battery. Place the new battery into the remote  
© 2005 directed electronics, inc.  
11  
 
control observing the correct polarity. When power is returned  
the remote control will display all icons in the LCD and generate  
all beeper tones once. Press any button on the remote to termi-  
nate the beeper tone review.  
your warranty  
It is necessary to retain your sales receipt, which reflects that the  
product was installed by an authorised dealer. For full details  
regarding your warranty coverage, please refer to the consumer  
warranty section of this guide.  
2-way LCD remote control functions  
The LCD remote control buttons are used to send commands to  
the system. The descriptions below reflect the standard configu-  
ration for this system. The buttons can be custom configured for  
the user’s specific needs by the installer. Also, the user can  
configure the LCD remote for certain responses (see  
Programming LCD Remote section).  
standard configurations  
Button  
The arming function is controlled by pressing this button for  
one second.  
Button  
The disarming function is controlled by pressing this button for  
one second.  
© 2005 directed electronics, inc.  
12  
 
Button  
Silent Mode™ and an optional auxiliary function are controlled  
by pressing this button. (Silent Mode™ works by pressing this  
button for less than one second before arming or disarming. An  
optional auxiliary function, such as boot release, can be  
controlled by pressing this button for 1.5 seconds.)  
This auxiliary output controls __________________________.  
Button  
Not used.  
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
This auxiliary output controls_________________________.  
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
This auxiliary output controls_________________________.  
© 2005 directed electronics, inc.  
13  
 
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
This auxiliary output controls_________________________.  
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
This auxiliary output controls_________________________.  
Program Button (on rear of LCD remote)  
Use this button to select the vehicle to control from the remote.  
Also use this button to configure response characteristics from  
the LCD remote (see Programming 2-Way Remote).  
standard LCD icon configurations  
Icon  
The transmit icon will be displayed while the remote control is  
transmitting a command to the vehicle.  
Icon  
The signal icon will be displayed if a command is transmitted to  
the vehicle but the command page is not received.  
© 2005 directed electronics, inc.  
14  
 
Icon  
The receive icon will be displayed while the remote control is  
receiving a page from the vehicle.  
Icon  
The auxiliary and sensor icons will display which auxiliary is oper-  
®
ating, or which security feature is in Warn Away or alarm state.  
Icon  
The garage door icon—for future use.  
and  
Icons  
®
The above Warn Away displays when a security feature has been  
tripped, but not to full alarm. These will display for 5-seconds.  
and  
Icons  
The above icons will display for 5-seconds when a security  
feature has been tripped to a full alarm condition.  
Icon  
The ultrasonic sensor (detects motion within the vehicle) icon  
will display for full alarm by flashing 5-times and displaying  
continuously until the page is cleared.  
Icon  
The tilt sensor icon will display for full alarm by flashing 5-times  
and displaying continuously until the page is cleared.  
© 2005 directed electronics, inc.  
15  
 
Icon  
The trunk (boot) icon will flash until the beep and/or vibrate  
stops then it will display continuously until the page is cleared.  
Icon  
The glass breakage sensor icon will display for full alarm by  
flashing 5-times and displaying continuously until the page is  
cleared.  
Icon  
®
The shock sensor icon will display for both Warn Away and full  
alarm by flashing 5-times and displaying continuously until the  
page is cleared.  
Icon  
The battery icon always displays the current charge capacity  
remaining in the remote’s battery.  
Icon  
The remote start (option) icon displays when the vehicle is being  
remote started.  
Icon  
The field disturbance sensor icon will display for both Warn  
®
Away and full alarm by flashing 5-times and displaying contin-  
uously until the page is cleared.  
Icon  
The ultrasonic sensor bar icon always displays the current sensi-  
tivity setting of the ultrasonic sensor.  
© 2005 directed electronics, inc.  
16  
 
Icon  
The ultrasonic sensor “sensor” icon will display for both Warn  
®
Away and full alarm by displaying continuously until the page  
is cleared.  
Icon  
The vibrate icon will always display if the remote is programmed  
for vibrate notification.  
Icon  
The ignition icon will display if the ignition is turned on when  
the vehicle’s doors are locked (alarm condition).  
Icon  
The hood (bonnet) icon will flash until the beep and/or vibrate  
stops then it will display continuously until the page is cleared.  
Icon  
The vehicle icon always displays the current vehicle (maximum  
®
of 4 vehicles) being controlled by the remote. If a Warn Away  
or alarm trigger should occur at one of the other vehicles, that  
vehicle’s number will be displayed and the LCD will display that  
vehicle’s status.  
Icon  
The door icon will flash until the beep and/or vibrate stops then  
it will display continuously until the page is cleared.  
© 2005 directed electronics, inc.  
17  
 
Icon  
The arm icon will flash when the system is locking the doors and  
display continuously until the system is disarmed.  
Icon  
The disarm icon will flash when the system is unlocking the  
doors and display continuously until the system is armed.  
transmitter functions  
This system uses a computer-based learn routine to learn the  
transmitter buttons. This makes it possible to assign any trans-  
mitter button to any system function. The transmitter initially  
comes programmed with Standard Configuration, but may also  
be customised by an authorised dealer. The buttons described in  
this manual correspond to a Standard Configuration transmitter.  
remote operation  
The system operates at 434 MHz and incorporates Directed’s propri-  
etary technology transceiver. The high frequency combined with  
Binary Data communication achieves superior range with two-way  
communication.  
system signal paging features  
A page is the signal the control module sends to the remote control  
as confirmation of receipt of a command or alarm system status.  
© 2005 directed electronics, inc.  
18  
 
When the remote control receives a page it will generate a page  
notification to the user (notifications are audible beeps and-or  
vibration) and the LCD Icons will display the current system status.  
Command Page  
When a command (arm/disarm, or auxiliary channel) from the  
remote control is sent and received, the system will send a  
command page back to confirm receipt.  
Alarm Page  
If the alarm system is triggered while armed, an Alarm Page will be  
sent to the remote control. When the remote receives an Alarm  
Page, the LCD icons will display the alarm system status informa-  
tion and the remote control will generate beeps and-or vibration.  
An Alarm Page alert is a series of 5 groups of 4 rapid beeps (ultra-  
sonic sensor, boot, door, ignition, or bonnet trigger) and the  
LCD icon that caused the alarm will display. This will repeat  
every 60 seconds to alert the user that the alarm system was trig-  
gered and will continue until the alarm page is cleared.  
Page Recognition (Acknowledgement)  
To clear a page alert/notification, quickly press any button on  
the remote control. This can be performed at any time during or  
after the page notification has occurred.  
The remote control will not send a command to the system at  
this time; it will only clear future repeats of the page notification.  
The next time a button is pressed on the remote control it will  
send a command to the system.  
© 2005 directed electronics, inc.  
19  
 
out of range notification  
If a command is issued from the remote, but the remote is set to  
the incorrect vehicle or is beyond the range of the vehicle to  
receive the command, the remote responds with 3 set of 2 quick  
beeps and the  
icon will flash 3-times.  
programming LCD remote  
To enter programming mode  
Press and hold the  
button until one long beep is heard.  
P
Programming mode to customise the remote’s response is now  
entered.  
note:  
If no buttons are pressed within 5-seconds, pro-  
gramming mode will exit with 2-beeps.  
Beeps/Vibration On/Off  
Press  
to select beeps/vibration On/Off. Beeps alone, or  
vibration alone, or beeps and vibration, or no beeps or vibration  
can be selected. Refer to the table below for these settings.  
© 2005 directed electronics, inc.  
20  
 
Beep/Vibrate settings  
Beeps only (default)  
Programming response Icon display*  
1-beep  
Siren icon On  
Vibrate only  
1-vibrate  
Vibrate icon On  
Vibrate and siren icon  
On  
Beep & Vibrate  
1-beep and 1-vibrate  
Vibrate and siren  
icons Off  
No Beep and No Vibrate 1 long beep  
*note:  
This is the icon displayed during programming.  
Illumination On/Off  
Press  
to select LCD backlight illumination On/Off. The  
LCD backlight will illuminate when a remote button is pressed,  
or a alarm status page is received.  
LCD Backlight settings Programming response  
ON  
1-beep, backlight ON  
2-beeps, backlight OFF  
OFF  
Page notification  
The remote control can be programmed to notify the user of a  
page (audibly beeping if the vehicle’s status changes, e.g. door  
unlocked, engine started, vehicle violation, etc.). On the LCD  
© 2005 directed electronics, inc.  
21  
 
remote press  
to select page On/Off. One beep is page On,  
Two beeps is page Off. When programmed off the remote will not  
give any notification that a page was received from the vehicle.  
note:  
no alarms  
will be notified to  
If programmed Off,  
the remote. Command information (armed/disarmed)  
will be notified to the remote.  
To exit programming mode  
The LCD remote control will exit programming mode after 5-  
seconds of inactivity and will emit 1 long beep.  
using your system  
The buttons described in this manual correspond to the standard  
configuration. Remember, this is not the only way your trans-  
mitter may be set up. It can be customised to meet your needs.  
active arming  
You can activate, or arm, the system by pressing  
on your  
transmitter for one second. When the system arms, you will hear  
a short siren sound, or chirp, and the indicator lights will flash  
once. If the vehicle’s central door locking has been connected to  
the system, the doors will lock.  
While the system is armed, the status LED will flash approxi-  
mately once per second, indicating that the system is actively  
© 2005 directed electronics, inc.  
22  
 
protecting your vehicle. If you hear a second chirp after arming,  
and see the status LED flashing in groups, refer to the Diagnostics  
section of this guide. This extra chirp is called Bypass Notification.  
The LCD remote responds to active arming with one beep and  
the  
icon will flash 5-times to indicate successful arming of  
the system.  
If the LCD remote beeps twice after arming, the system has detected  
an active sensor that should be checked. For example, a door open  
icon will be displayed flashing 5-times on the LCD screen.  
passive arming  
The system also can be programmed to arm itself automatically  
(called passive arming). If the system is programmed for passive  
arming, it will automatically arm 30 seconds after the ignition is  
turned off and the system "sees" you leave the vehicle by opening  
and closing a door. Whenever the system is in its 30-second  
passive-arming countdown, the status LED will flash twice as  
fast as it does when the system is armed. The siren will chirp  
once 20 seconds after the last door has been closed and the inte-  
rior light has turned off. The system is not actually armed at that  
point. The system arms and the doors lock (if connected and  
programmed for passive locking) at the 30 second mark, but the  
siren will not chirp. The early chirp provides you with a 10-  
second warning prior to arming.  
© 2005 directed electronics, inc.  
23  
 
note: If any protected entry point (such as a door or a  
switch-protected (boot or bonnet)) is open, the system  
will not passively arm (unless forced passive arming is  
programmed on). See Programming Options section of  
this guide. Additionally, each time a protected entry is  
triggered during the arming countdown, the 30-second  
countdown starts from the beginning.  
When armed your vehicle is protected as follows:  
Movement inside the passenger compartment will trigger  
the system. The triggered sequence is 30 seconds of constant  
siren and indicator light flashing.  
If a door is opened, the system will immediately trigger.  
Turning on the ignition key will trip the same two-stage  
response as opening a door.  
The built-in triple circuit Immobiliser prevents the vehicle's  
ignition, starter and fuel pump from operating.  
Any full trigger of the alarm system will immediately send an  
alarm page to your remote informing you that your vehicle  
should be checked.  
© 2005 directed electronics, inc.  
24  
 
one-time bypass  
This feature stops the alarm from arming or activating any  
outputs that are programmed to activate when the alarm is  
armed.  
One-time bypass will defeat the following actions:  
Passive arming: If programmed ON the alarm will not arm  
itself.  
If the remote is used to arm the alarm after exiting the vehicle:  
Window roll up: If programmed ON this output will not  
activate.  
Linked Auxiliary Outputs: If programmed to activate on  
arm, they will not activate.  
To activate one-time bypass:  
1. After parking turn the ignition off.  
2. Turn the ignition On for more than 1-second and less than  
3-seconds.  
3. The siren will chirp once to indicate one-time bypass has  
been activated.  
To cancel one-time bypass perform one of the following:  
Arm then disarm the alarm.  
Turn the ignition On for more than 3-seconds.  
© 2005 directed electronics, inc.  
25  
 
transmitter sensor disable  
To temporarily disable a sensor input, arm the system. Press the  
button again and the system will respond with 3 indicator  
flashes. This means all sensor warn-away triggers are bypassed.  
Press the  
button again and the system will respond with 4  
indicator light flashes. This means all sensor warn-away and full  
triggers are bypassed.  
autoimmobilisation  
The built-in Triple Circuit Immobiliser will automatically arm  
(indicated by a slow LED flash), 30 seconds after the ignition is  
turned off. (This feature is a Thatcham and EC requirement and,  
therefore, is not user-programmable.) To disarm the Immobiliser  
when it has AutoImmobilised, either use the remote control to  
arm and then disarm the system, or turn the ignition on and  
press the  
or  
button or enter your 4-digit PIN code.  
disarming  
To disarm the system, press  
. You will hear two chirps, and  
the indicators will flash twice. If the vehicle's central locking is  
connected to the system, the doors will unlock. If the siren chirps  
either four or five times when disarming, refer to the Diagnostics  
section of this guide. This is called Tamper Alert and means the  
system has triggered while you were away.  
© 2005 directed electronics, inc.  
26  
 
high security disarm  
This security system offers High Security Disarm. High Security  
Disarm is a feature that makes it possible to silence and reset the  
system while it is triggering, without disarming the system. If the  
system is triggered and the siren has been sounding for longer  
than six seconds, pressing  
or  
on the remote transmitter  
will stop the trigger and return the unit to the armed state. The  
system will not disarm, but rather reset. This prevents you from  
disabling the system should you wish to disarm it without visu-  
ally checking the vehicle. Pressing  
after resetting the system  
will disarm the system; pressing this button during the first six  
seconds of the triggered sequence will disarm the security system  
immediately. The six second timer is provided for your conve-  
nience, in case the system is accidentally triggered.  
The remote will indicate disarm notification with 2 beeps and 5  
flashes of the  
icon. If disarming after the system has been  
triggered, the remote control will send a diagnostic notification  
as a reminder. These diagnostic notifications are:  
1. If a sensor triggered the system, the remote will emit 4 quick  
beeps and the LCD screen will indicate which sensor (5-  
flashes) tripped the alarm.  
2. If a switch (Zone 1, 3, 5, or 6) triggered the system, the  
remote will emit 4 quick beeps and the LCD screen will  
indicate which switch (5-flashes) tripped the alarm.  
© 2005 directed electronics, inc.  
27  
 
disarming without a transmitter  
This feature allows you to disarm the system without the trans-  
mitter should it be lost, damaged, or disabled. In order to disarm  
without a transmitter, you must have the vehicle’s ignition key,  
know where the Valet switch is located, and have the PIN code.  
Check with the installer for the location of the Valet switch.  
Please refer to the Disarm/Valet Mode section of this guide for  
instructions to enter the pin code.  
Location of Valet switch____________________________________.  
PIN code_________________________________________________.  
The LCD remote will indicate disarm notification with 4 quick  
beeps and 5 flashes of the  
and triggered zone icons.  
entering your PIN  
Entering your PIN code using the valet switch allows you to  
disarm the system without using the transmitters. Your 4-digit  
PIN code is noted on the back page of this manual. If you would  
like to change this PIN for one that is easier for you to remember  
please visit your installing dealer.  
1. Turn the ignition key to the ON position.  
2. Within 10 seconds, enter the first number in your PIN.  
Press and release the Valet switch the same number of times  
as the first digit in your PIN.  
Example:  
times.  
If your PIN is 2345, press the Valet switch two  
© 2005 directed electronics, inc.  
28  
 
3. Turn the ignition key OFF.  
4. Turn the ignition key to the ON position.  
5. Enter the second number in your PIN (press the Valet switch  
three times).  
6. Turn the ignition key OFF.  
7. Turn the ignition key to the ON position  
8. Enter the third number in your PIN (press the Valet switch  
four times).  
9. Turn the ignition key OFF.  
10. Turn the ignition key to the ON position.  
11. Enter the last number in your PIN (press the Valet switch  
five times).  
12. Turn the ignition key OFF. If you have entered the correct  
code you will hear two chirps. Should you hear five rapid  
chirps, the correct code has not been entered. Begin entering  
your PIN from the beginning.  
interior light control  
security only  
The interior light activates for 30-seconds after the system is  
disarmed.  
Ignition controlled  
The interior light activates for 30-seconds after the ignition is  
turned Off.  
© 2005 directed electronics, inc.  
29  
 
door controlled  
The interior light activates for 30-seconds after the system sees a  
door has closed. (If door was held open for longer than 3  
minutes the interior light will not illuminate.)  
full  
The interior light activates for 30-seconds after seeing door  
closure, ignition, or security disarm. (This is the factory setting.)  
silent mode  
To arm or disarm the system without siren chirps, use Silent  
Mode™. Simply press  
for less than one second before  
arming or disarming, and the confirmation chirp(s) will be elim-  
inated for that one operation only. If you want the arm/disarm  
chirps turned off permanently, your dealer can do this for you.  
®
note: The Warn Away response from any optionally  
installed sensors are bypassed if the system is armed using  
Silent Mode. This ensures that no chirps will be emitted  
by the siren in an area you want chirp-free. The system is  
®
still fully capable of triggering. Only the Warn Away  
response is bypassed.  
valet mode  
You can prevent your security system from automatically arming  
and triggering by using Valet Mode. This is very useful when  
washing the vehicle or having it serviced. In Valet Mode, the  
security system will not arm, even with the remote transmitter,  
but all convenience functions (door locks, boot release, etc.) will  
continue to work normally.  
© 2005 directed electronics, inc.  
30  
 
To enter Valet Mode:  
1. Turn the ignition on.  
2. Turn the ignition off.  
DRW-35  
3. Press and release the Valet  
button within 10 seconds.  
The status LED will light solidly to indicate the system has  
entered Valet Mode.  
To exit Valet Mode:  
1. Turn the ignition on. The system will then automatically  
exit Valet mode.  
To enter or exit Valet Mode using the transmitter:  
1. Open any vehicle door.  
2. Press  
3. Press  
4. Press  
.
.
again.  
The status LED will light solidly if you are entering Valet Mode,  
and it will go out if you are exiting Valet Mode.  
© 2005 directed electronics, inc.  
31  
 
diagnostics  
The microprocessor at the heart of your security system is  
constantly monitoring all of the switches and sensors that are  
connected to it. It detects any faulty switches and sensors and  
prevents them from disabling the entire system. The micropro-  
cessor will also record and report any triggers that occurred  
during your absence. Refer to the System Status Chirps and  
Table of Zones charts for diagnostic information.  
arming diagnostics  
If the system is armed while an input is active (door open, sensor  
triggering, etc.) the unit will chirp once when arming and then  
one more time a few seconds later. This is called Bypass  
Notification.  
note: Bypass Notification will not occur when using  
Silent Mode™ or if chirps have been programmed OFF.  
The security system will ignore the input that was active when  
the system was armed, until the input goes away. Three seconds  
later the system will monitor that input normally. For example,  
if your vehicle’s boot was open, and you arm the system, you  
will hear Bypass Notification chirps. If you close the boot it is  
then monitored normally without the need to disarm and then  
rearm the system.  
© 2005 directed electronics, inc.  
32  
 
disarming diagnostics  
Extra disarm chirps are the Tamper Alert. If four chirps are heard  
when disarming, the system was triggered in your absence. If five  
chirps are heard, a zone was triggered so many times that Nuisance  
®
Prevention Circuitry has bypassed that zone. The status LED will  
indicate which zone was involved. (See Table of Zones section of  
this guide.) The system will retain this information in its memory,  
and continue to chirp four or five times each time it is disarmed,  
until the next time the ignition key is turned on.  
system status chirps  
The siren will chirp when arming/disarming the system. The  
pattern of chirps will audibly report the system’s status as  
described below.  
Action  
Arm  
Number of Chirps  
1
Description  
System armed  
Arm  
1 (3-second delay), 1  
System armed with  
Bypass Notification  
Disarm  
Disarm  
2
4
System disarmed  
System disarmed with  
Tamper Alert  
© 2005 directed electronics, inc.  
33  
 
table of zones  
The zone number is the number of LED flashes used by the  
system to identify that input. The standard input assignments  
are listed below, along with spaces to write in any optional  
sensors or switches you have had installed.  
Zone - Number  
of LED Flashes  
Dealer-Installed  
Options  
Description  
1
2
3
4
5
6
7
Boot trigger  
Ultrasonic Sensors  
Door switch trigger  
Optional sensor input 1  
Ignition trigger  
Bonnet trigger  
Optional sensor input 2  
interpreting zone diagnostics  
Warn Away responses are not reported by arming or disarming  
diagnostics. If you receive a Bypass notification when arming or  
a Tamper Alert notification when disarming, look at the LED.  
Active or triggered zones will be indicated by a pattern of flashes  
by the LED.  
© 2005 directed electronics, inc.  
34  
 
Example  
If Zone 3 was active or triggered, the LED will flash three times  
with a two-second pause. Then it will flash three times again,  
and repeat until the ignition is turned on.  
note: Your system stores the last six triggered zones in  
memory. If your system has been triggered but the LED  
has been reset by turning on the ignition, your dealer can  
still recall the last six zones that were triggered. Contact  
your dealer for details.  
code hopping  
The receiver and transmitters each use mathematical formulas  
called algorithms to change their codes each time the transmitter  
is used. This technology has been developed to increase the secu-  
rity of the unit. The control unit knows what the next codes  
should be. This helps to keep the transmitter "in sync" with the  
control unit even if you use the remote control out of range of  
the vehicle. However, if the transmitter has been pressed many  
times out of range of the vehicle, or if the battery has been  
removed, it may get out of sync with the control unit and fail to  
operate the system. To re-sync the remote control simply press  
of the transmitter several times within range of the vehicle.  
The alarm will automatically re-sync and respond to the trans-  
mitters normally.  
© 2005 directed electronics, inc.  
35  
 
high frequency  
Your system transmits and receives at 433 MHz. This provides a  
cleaner spectrum with less interference and a more stable signal.  
owner recognition  
Owner Recognition is a feature available exclusively from Directed.  
®
Using the Directed Bitwriter , a hand-held programming tool,  
your dealer can program many of the system settings. The  
programmer makes it possible to program different settings for  
each transmitter that is used with the system. Then, whenever a  
specific transmitter is used, the system will recall the settings  
assigned to that transmitter. Owner Recognition lets up to four  
users of the system have different settings that meet their specific  
needs. It is almost like having four separate alarms in your vehicle,  
one for each user.  
note: Owner Recognition cannot be programmed with-  
out a Directed Bitwriter® and the necessary software.  
Check with your dealer for more information.  
rapid resume logic  
This Directed system will store its current state to non-volatile  
memory. If power is lost and then reconnected, the system will  
recall the stored state from memory. This means if the unit is in  
© 2005 directed electronics, inc.  
36  
 
Valet Mode and the battery is disconnected for any reason, such  
as servicing the car, when the battery is reconnected the unit will  
still be in Valet Mode. This applies to all states of the system  
®
including arm, disarm, Autoimmobilised, VRS , and Valet  
Mode.  
power saver mode  
Your system will automatically enter Power Saver Mode while  
armed or in Valet Mode, after a period of time in which no oper-  
ation has been performed. This lowers the current draw to the  
vehicle’s battery. Power Saver Mode takes over under the  
following conditions:  
Power Saver when the system is armed: After the system has  
been armed for 24 hours, the LED will flash at half its  
normal rate, decreasing the system's current draw.  
Power Saver in Valet Mode: When the system enters Valet  
Mode the LED illuminates steadily. If the vehicle is not used  
(ignition is not turned on) for a period of one hour while the  
system is in Valet Mode, the LED will turn off.  
© 2005 directed electronics, inc.  
37  
 
programming  
Programming options control what your system does during  
normal operation, and require few or no additional parts.  
However, some may require additional installation labour.  
The following is a list of the program settings, with the factory  
Bold:  
settings in  
Active arming  
(only with the transmitter) or passive arming (au-  
tomatic arming 30-seconds after the last door has been closed).  
on  
Arming/disarming confirmation siren chirps  
or off.  
off  
The ignition controlled door lock feature on or : With  
this feature on, the doors will lock three seconds after the  
ignition is turned on, and the doors closed. The system will  
not lock the doors when the ignition is turned on with any  
door open.  
off  
Ignition controlled door unlock on or . With this feature  
on the doors will unlock when the ignition is turned off.  
active door  
Passive door locking (with passive arming) or  
locking  
(only when arming with the transmitter). Passive  
locking allows the vehicle's doors to lock when the security  
system passively arms (after the 30 second countdown). This  
feature only works if passive arming has been programmed on.  
off  
Forced passive arming on or  
: If your system is  
programmed for passive arming and the forced passive  
arming feature has been programmed on, the system will  
passively arm after one hour, even if a protected entry has  
© 2005 directed electronics, inc.  
38  
 
been left open. This feature is useful if a door has been left  
ajar when leaving the vehicle. Forced passive arming ensures  
that the security system will be armed in every situation.  
Vehicle Recovery System (VRS): Refer to section later in this  
guide.  
PIN code change: Your 4-digit PIN code is noted on the  
back page of this manual. If you would like to change this  
PIN for one that is easier for you to remember please visit  
your installing dealer.  
Siren chirp volume: Battery back-up siren consists of a dual-  
tone sequence. The siren chirps can be either full volume or  
six decibels quieter  
than normal.  
vehicle recovery system (vrs®)  
®
The optional VRS feature is designed to ensure that any un-  
authorised user of your vehicle (even if using your keys and remote  
control) will not be able to permanently separate you from your  
vehicle.  
®
The VRS cannot prevent a carjacking attempt; however, it does  
ensure that if your vehicle is taken by an unauthorised user, it will  
be disabled (after several progressive warnings) as safely as  
®
possible. Should a carjacking occur, the VRS allows you to  
concern yourself with your personal safety without worrying  
about your property.  
© 2005 directed electronics, inc.  
39  
 
Directed has engineered this vehicle security system, and the  
®
VRS feature to provide the best combination of personal safety  
and property protection available. When properly installed, the  
system can never inadvertently stop your vehicle in traffic or in  
a dangerous position while the vehicle is in operation. It is unlike  
other systems that shut down your engine while it is running.  
This system is designed to perform full triple-circuit immobili-  
sation.  
important! Any installation that allows this product to  
shut down a vehicle's engine when it is running is con-  
trary to the product’s design and intended usage, and  
Directed hereby expressly disclaims any liability resulting  
therefrom.  
arming the vrs®  
To arm the VRS , turn the ignition to the ON position and press  
®
the arm button on the remote transmitter for one second. The  
indicator lights will flash and the siren will chirp once. This can  
be done before driving or while driving the vehicle. Once the  
system is armed, it will initiate its triggered sequence (see below)  
if any door is opened and closed. The system will now trigger au-  
tomatically the next time you or anyone drives the vehicle. This  
helps to protect the vehicle if someone takes your keys and remote  
control.  
®
note: If the VRS system is armed while operating the vehi-  
cle and not disarmed prior to leaving the vehicle, it is still  
armed and will trigger the next time the vehicle is driven.  
© 2005 directed electronics, inc.  
40  
 
vrs® triggered sequence  
Fifteen seconds after the last door has closed, the system’s status  
LED will begin flashing. This delay is intended to allow you time to  
distance yourself from your vehicle in the event of a carjacking.  
Forty-five seconds later, the siren begins chirping and the indi-  
cator lights begin flashing.  
Fifteen seconds after the siren chirps begin, the siren’s output will  
change to a continuous blast.  
®
From this point on, when the ignition key is turned off, the VRS  
will immediately turn on the triple circuit immobiliser to prevent  
the vehicle from being restarted.  
Three minutes after the constant siren output begins, the flashing  
indicator lights and the siren will stop. The immobiliser will  
remain active until the system is disarmed. If the door is opened  
or the ignition is turned off and on in an attempt to restart the  
car, the siren and light flashing will begin again.  
© 2005 directed electronics, inc.  
41  
 
disarming the vrs®  
Take the time to familiarise yourself with the VRS triggering se-  
quence and the disarm procedure. It is important to recognise  
®
®
and identify the VRS trigger sequence and know how to disarm  
it in case of accidental activation.  
®
Once the VRS is armed, it does not disarm automatically. You  
must disarm it the next time you operate the vehicle. You must  
disarm it with one of the following procedures:  
If the system has not entered the triggered sequence (siren has  
not started chirping):  
1. Turn the ignition on.  
2. Press the  
button on the remote for one  
second. The lights will flash and the siren will  
chirp twice.  
If the system has entered the triggered sequence (siren has begun  
chirping), pressing the  
button of the remote will not disarm  
®
®
®
VRS . To disarm the VRS during a VRS trigger sequence:  
1. Turn the ignition on.  
2. Begin entering your 4-digit PIN  
DRW-35  
code as noted in the Entering  
Your PIN section of this guide.  
© 2005 directed electronics, inc.  
42  
 
programming options  
See your dealer for further details on the options listed below  
available with this system.  
Comfort Closure: Windows will close upon locking the vehicle.  
Dual Sensor Trigger: If programmed, both the onboard and at  
least one of the optional sensors need to be triggered within 1-  
second of each other for full alarm.  
note: In dual sensor mode, the LCD remote will report  
showing both zones that tripped the alarm. The in-vehicle  
LED will flash to indicate only the last sensor of the pair  
which tripped the alarm.  
Forced Passive Arming: If passive arming is on and a door is left  
open the system will be armed after 1-hour.  
High Security Disarm: If the system is triggered this feature allows  
the user to silence the siren and reset the system to the armed  
state without having to visually check the system status.  
Remote Start Reporting: This channel 3 programmable option  
allows for the 2-way LCD transmitter to report when the vehicle  
has been remote started provided the 561T remote starter has  
been installed.  
Retained Accessory Power: This output from the security system  
can be connected to vehicle accessories, such as the vehicle radio.  
After the ignition has been turned off, it will continue to supply  
power until a door has been open and closed.  
© 2005 directed electronics, inc.  
43  
 
ultrasonic sensors  
Your security system incorporates two Ultrasonic sensors, which  
are most commonly mounted at the top of the A-pillars facing  
the rear of the vehicle. These sensors detect movement inside the  
vehicle by sensing air disturbance. They should trigger the alarm  
if a thief gained access to the interior of your vehicle. Please make  
sure all windows are closed on the vehicle or the ultrasonic  
sensors could false alarm due to air movement.  
The sensor bar indicator  
on the LCD of the  
remote displays the current sensor sensitivity setting. Increased  
sensitivity is indicated if the bar is filled to the right.  
note:  
Return your vehicle to your dealer for ultrasonic sen-  
sor sensitivity adjustment.  
security & convenience expansions  
Here we have listed only some of the many expansion options  
available. Please contact your dealer for a complete explanation  
of all the options available to you.  
Glass Tamper Sensor: Metal on glass, glass cracking, and  
breaking glass each produce distinctive acoustic signatures. The  
506T glass tamper sensor uses a microphone to pick up sounds,  
and then analyzes them with proprietary acoustic software to  
determine if the glass has been struck.  
© 2005 directed electronics, inc.  
44  
 
Field Disturbance Sensor: An invisible dome of coverage is estab-  
lished by installing the 508D "radar" sensor. Your security  
system can then react to any intrusions into this field with the  
triggered sequence.  
®
Headlight Automation: The 545T Nite-Lite will automatically  
turn on your headlights when it gets dark. In addition, the 545T  
will turn your headlights on whenever the windscreen wipers are  
used. A transmitter function can also be used to turn on your  
headlights for a programmed time.  
Electric Boot Release: The channel two output of the system can  
operate a factory boot release for the vehicle’s boot or hatch. (An  
additional relay may be required.) If the factory release is not  
electrically activated, then Directed's 522T boot release solenoid  
can often be added.  
Electric Window Control: Automatic electric window control is  
provided with the 529T and 530T systems.  
Valet Start System: For the ultimate in convenience, the Valet  
561T* start system can start your vehicle, monitor engine func-  
tions, and power your climate control system with a push of a  
button. Over-rev protection, open-bonnet lockout, brake pedal  
shutoff, and automatic timer shutoff are all included. (This  
feature is only for automatic transmission, fuel-injected vehicles.)  
*This accessory is not evaluated by Thatcham.  
© 2005 directed electronics, inc.  
45  
 
glossary of terms  
ASK Amplitude Shift Keying—a method of transmitting data.  
Control Unit: The "brain" of your system. Usually hidden under  
the dash area of the vehicle. It houses the microprocessor which  
monitors your vehicle and controls all of the system's functions.  
Input: A physical connection to the system. An input can be  
provided by a sensor, pinswitch or through an existing system in  
the vehicle, such as ignition or courtesy lights.  
In-vehicle status LED: A light mounted somewhere in the vehicle.  
It is used to indicate the status of your system. It is also used to  
report triggers and faults in the system or sensors.  
LCD: This is a Liquid Crystal Display used on your remote trans-  
mitter to display your vehicles status/alarm information.  
LED: A light mounted somewhere in the vehicle. It is used to  
indicate the status of your system. It is also used to report trig-  
gers and faults in the system or sensors.  
Siren: Noise generating device usually installed in the engine  
compartment of the vehicle. It is responsible for generating the  
"chirps" you hear, as well as the tones you hear while the alarm  
is triggered.  
Transmitter: Hand-held, remote control which operates the  
various functions of your system.  
© 2005 directed electronics, inc.  
46  
 
Trigger or Triggered Sequence: This is what happens when the  
alarm "goes off" or "trips". The triggered response of your  
system consists of the siren sounding and indicator light flashing  
for the programmed duration.  
Valet Button: A small push-button switch mounted somewhere  
inside the vehicle. It is used to override the alarm when a trans-  
mitter is lost or damaged, or to enter or exit Valet mode.  
Zone: A zone is a separate input that the alarm can recognise as  
unique. Each input to the system is connected to a particular  
zone. Two or more inputs often share the same zone.  
© 2005 directed electronics, inc.  
47  
 
© 2005 directed electronics, inc.  
48  
 
health check  
Directed Electronics recommends you return to your installing Viper  
dealer to have your system checked for correct operation. The first  
check is due one year after the installation date and at yearly intervals  
thereafter.  
note:  
There may be a small charge incurred for this service.  
© 2005 directed electronics, inc.  
49  
 
Your factory set 4-digit PIN code is noted below. See this manual for  
information on using your PIN code.  
place sticker here  
The company behind this system is Directed Electronics, Inc.  
E&OE, specification is subject to change without notice. Some vehicles require optional  
parts/wiring and a few are incompatible with some features.  
Directed® is committed to delivering world-class quality products and services  
that excite and delight our customers.  
Directed Electronics UK office  
Unit C Longmead Business Centre  
Blenheim Road  
Epsom, Surrey KT19 9QQ  
Directed Electronics, Inc.  
Vista, CA 92081  
© 2005 Directed Electronics, Inc. - All rights reserved  
G480V 04-05  
 

Toshiba Laptop 530 User Manual
Toshiba Printer B 480 QQ User Manual
Toshiba Projector TDP D1 US User Manual
TP Link Network Router TD W8910GB User Manual
Tricity Bendix Dishwasher DH 102 User Manual
Uniden Telephone WDECT 2345+1 User Manual
VDO Dayton Car Stereo System CD1537x User Manual
Vulcan Hart Convection Oven SG4D User Manual
Wagner SprayTech Paint Sprayer 1420 User Manual
Weed Eater Blower 545117525 User Manual